Silindriline lihvimismasin - UniversalKELLENBERGER
Kel-Varia UR225-1500 FANUC
Silindriline lihvimismasin - Universal
KELLENBERGER
Kel-Varia UR225-1500 FANUC
Tootmisaasta
2002
Seisund
Kasutatud
Asukoht
Kirchheim unter Teck 

Põhiandmed
- Masina nimetus:
- Silindriline lihvimismasin - Universal
- Tootja:
- KELLENBERGER
- Mudel:
- Kel-Varia UR225-1500 FANUC
- Tootmisaasta:
- 2002
- Seisund:
- kasutatud
Hind ja asukoht
- Asukoht:
- 73230 Kirchheim

Helistada
Pakkumise üksikasjad
- kuulutuse ID:
- A17404443
- Viitenumber:
- 1056-M24Vari
- Värskendus:
- viimati kuupäeval 10.11.2026
Kirjeldus
grinding diameter 450 mm
grinding length 1500 mm
centre height 225 mm
Control FAGOR
NEW: New CNC Control FANUC with Blue Solution
EQUIPEMENT
- T1: grinding wheel diameter 500 mm
- T2: grinding wheel diameter 400 mm
- T6: HF Fischer spindle MFV or MFZ 1224/1242/1260
- T7: HF Fischer spindle MFV or MFZ 1224/1242/1260
- Marposs tool measurement
- active longitudinal positioning
- Elaso GAP-control on T1 and T2
contactless integrated in the control surface
- Elaso GAP internal grinding with fluid sensor for T6 and T7
- semi-automatic balancing by Elaso
integrated in the control surface for T1/T2
- tailstock hydraulic with fine adjustment +/- 150 microns
- dresser on workpiece spindle side table mounted
- dresser on tailstock side table mounted
- dresser on upper table
- new service- and userfriendly housing
Isdpfx Akjuxfu Noieii
SPECIAL EQUPEMENT:
Workhead with direct drive
- strongly recommended for
non-circular grinding
- workpiece weight flying max. 75kg
- workpiece weight between centres 150kg
- water-cooled
B-axis with direct drive
- center height 225 mm
- extremely torsionally stiff
- highly accurate positioning
- resolution °
- water-cooled
Hydrostatic ball screw - x-axis
- wear-free, as there is no contact during operation
- no loss of precision, even during long-term use at full load and
maximum speed
- no friction at low speeds
- no friction force backlash when the direction of rotation changes
- translates even the smallest rotational movements
- no stick-slip effect even at low speeds
- no fluctuations in frictional torque due to ball circulation
- higher axial stiffness compared to ball screws
- significant improvement in damping, resulting in better workpiece surface
finish and tool life
- no oscillations due to ball circulation
- also suitable for high speeds and accelerations
- cost-effective alternative to the linear motor with greater precision and
significantly lower heat generation
- significantly less power dissipation and, as a result, no problems with swarf
on permanent magnets
New hydraulic unit
- optimized temperature control (chiller)
- Energy-saving
Only one pump controlled by VFD
- Pressure monitoring
- monitoring of the hydrostatic oil for
water content.
(Damage to the bellows is recognised and detected prematurely)
-fine adjustment +/- 150 microns
Paper belt filter
375l – alternative 480l
Grinding mist extraction system – emulsion
MECHANICAL OVERHAUL
-complete machine according to Kellenberger protocoll
-new painting
ELECTRICAL OVERHAUL
- new modern Fagor CNC with BEMA HMI
- new electric cabinet
- new digital drive technology
- replacement of all electrical cables, switches etc.
- new absolute external scales in x- and z-axis
- new absolute encoder (B-axis)
Grinding software BEMA-Standard:
- workpiece zeroing
- grinding wheel zeroing
- dressing diamond measuring
- corrections
- external and internal surface grinding
- external and internal angle grinding
(turning of the b-axis, dressing with straight wheel)
- external and internal radius grinding (radius dressed on wheel)
- semi-automatic traverse grinding
- workpiece zeroing
- 2 dressing diamonds
- 1 dressing blade
- dressing roll
- 3 flat dresser
- corrections
- Z-position measurement
- GAP control
Optional grinding cycles at no extra charge:
Profile plunge grinding:
- external and interna...
grinding length 1500 mm
centre height 225 mm
Control FAGOR
NEW: New CNC Control FANUC with Blue Solution
EQUIPEMENT
- T1: grinding wheel diameter 500 mm
- T2: grinding wheel diameter 400 mm
- T6: HF Fischer spindle MFV or MFZ 1224/1242/1260
- T7: HF Fischer spindle MFV or MFZ 1224/1242/1260
- Marposs tool measurement
- active longitudinal positioning
- Elaso GAP-control on T1 and T2
contactless integrated in the control surface
- Elaso GAP internal grinding with fluid sensor for T6 and T7
- semi-automatic balancing by Elaso
integrated in the control surface for T1/T2
- tailstock hydraulic with fine adjustment +/- 150 microns
- dresser on workpiece spindle side table mounted
- dresser on tailstock side table mounted
- dresser on upper table
- new service- and userfriendly housing
Isdpfx Akjuxfu Noieii
SPECIAL EQUPEMENT:
Workhead with direct drive
- strongly recommended for
non-circular grinding
- workpiece weight flying max. 75kg
- workpiece weight between centres 150kg
- water-cooled
B-axis with direct drive
- center height 225 mm
- extremely torsionally stiff
- highly accurate positioning
- resolution °
- water-cooled
Hydrostatic ball screw - x-axis
- wear-free, as there is no contact during operation
- no loss of precision, even during long-term use at full load and
maximum speed
- no friction at low speeds
- no friction force backlash when the direction of rotation changes
- translates even the smallest rotational movements
- no stick-slip effect even at low speeds
- no fluctuations in frictional torque due to ball circulation
- higher axial stiffness compared to ball screws
- significant improvement in damping, resulting in better workpiece surface
finish and tool life
- no oscillations due to ball circulation
- also suitable for high speeds and accelerations
- cost-effective alternative to the linear motor with greater precision and
significantly lower heat generation
- significantly less power dissipation and, as a result, no problems with swarf
on permanent magnets
New hydraulic unit
- optimized temperature control (chiller)
- Energy-saving
Only one pump controlled by VFD
- Pressure monitoring
- monitoring of the hydrostatic oil for
water content.
(Damage to the bellows is recognised and detected prematurely)
-fine adjustment +/- 150 microns
Paper belt filter
375l – alternative 480l
Grinding mist extraction system – emulsion
MECHANICAL OVERHAUL
-complete machine according to Kellenberger protocoll
-new painting
ELECTRICAL OVERHAUL
- new modern Fagor CNC with BEMA HMI
- new electric cabinet
- new digital drive technology
- replacement of all electrical cables, switches etc.
- new absolute external scales in x- and z-axis
- new absolute encoder (B-axis)
Grinding software BEMA-Standard:
- workpiece zeroing
- grinding wheel zeroing
- dressing diamond measuring
- corrections
- external and internal surface grinding
- external and internal angle grinding
(turning of the b-axis, dressing with straight wheel)
- external and internal radius grinding (radius dressed on wheel)
- semi-automatic traverse grinding
- workpiece zeroing
- 2 dressing diamonds
- 1 dressing blade
- dressing roll
- 3 flat dresser
- corrections
- Z-position measurement
- GAP control
Optional grinding cycles at no extra charge:
Profile plunge grinding:
- external and interna...
Pakkuja
Märkus: Registreeru tasuta või logi sisse, et saada kogu teave.
Registreeritud alates: 2002
47 Kuulutused internetis
Saada päring
Telefon & Faks
+49 7021 ... kuulutused
Need kuulutused võivad samuti teile huvi pakkuda.
Edukas
Teie sõnum on saadetud.
Väike kuulutus
Dortmund
1 358 km
Käitavad tööriistahoidikud sirged
NACKE + WTOVDI 50
NACKE + WTOVDI 50
Edukas
Teie sõnum on saadetud.
Väike kuulutus
Saksamaa
1 242 km
CNC pinna lihvimismasin
JungJE600
JungJE600
Edukas
Teie sõnum on saadetud.
Väike kuulutus
Offenbach an der Queich
1 512 km
Lõike- ja tsentreerimismasin
UMA - SZMSZM 100/1000
UMA - SZMSZM 100/1000
Edukas
Teie sõnum on saadetud.
Väike kuulutus
Mönchengladbach
1 445 km
Koordinaatmõõtmismasin
MitutoyoCrysta Apex C776
MitutoyoCrysta Apex C776
Edukas
Teie sõnum on saadetud.
Väike kuulutus
Contamine-sur-Arve
1 868 km
Cnc multispindel automaatne treipingi
INDEXMS32C
INDEXMS32C
Edukas
Teie sõnum on saadetud.
Väike kuulutus
Ybbs an der Donau
1 331 km
FTIR spektromeeter - NICOLET IS20
ThermoFisher ScientificNICOLET IS20
ThermoFisher ScientificNICOLET IS20
Edukas
Teie sõnum on saadetud.
Väike kuulutus
Hövelhof
1 276 km
Twist drill ja avardamine lihvimine
Rohde&Doerrenberg (May)SS 40U
Rohde&Doerrenberg (May)SS 40U
Edukas
Teie sõnum on saadetud.
Väike kuulutus
Brügg
1 737 km
CNC SILINDRILINE LIHVIMISMASIN
KELLENBERGERKEL-VARIA R175 x 1500
KELLENBERGERKEL-VARIA R175 x 1500
Edukas
Teie sõnum on saadetud.
Väike kuulutus
Saksamaa
1 242 km
Liikuva sambaga freespink
ANAYAKHVM-6000-P
ANAYAKHVM-6000-P
Edukas
Teie sõnum on saadetud.
Väike kuulutus
Saksamaa
1 513 km
Schaudt Mikrosa SASL 125
Schaudt MikrosaSASL 125
Schaudt MikrosaSASL 125
Teie kuulutus on edukalt kustutatud
Ilmnes viga





















































































